Motorcycle BMW Sizes
TAP GUIDES INSURE THAT THREADS ARE SQUARE TO SURFACE.

The lower portion of the tap guide should remain as square as possible to the engine surface.
Turn the tap slowly while making sure the guide remains flush.
 

TAP GUIDES 

METRIC SIZE   PART NO.
M5x0.8   35086
M6x1.0   36105
M7x1.0   37105
M8x1.25   38125
M9x1.25   39125
M10x1.0   30105
M10x1.25   30125
M10x1.5   30155
M11x1.25   31125
M11x1.5   31155
M12x1.25   32125
M12x1.5   32155
M12x1.75   32175
M13x1.5   33155
M14x1.5   34155
M14x2.0   34255
M16x1.5   36155
M16x2.0   36205
M18x1.5   38155
M20x1.5   30215
M22x1.5   32255
M24x1.5   32455

 

INCH SIZE   PART NO.
1/4-20   31420
1/4-28   31420
5/16-18   35168
5/16-24   35168
3/8-16   33816
3/8-24   33824
7/16-14   37164
7/16-20   37162
1/2-13   31213
1/2-20   31225
5/8-18   25885
3/4-10   33415
3/4-16   33416

 

For Use in Restricted Areas
Ideal for use in areas where a T handle won't fit. Set of 8 sockets fits all number and fractional M.C.T.I. standard taps thru 1/2". A lso fits 1/8" NPT taps and metric taps thru 12mm manufactured to M.C.T.I. standards. Sockets contained on a vinyl holder.

Time-Sert taps 4mm to 12mm metric / 4-40 to 1/2 inch. 
Sockets #1 thru #4 use 1/4 drive,
rest use 3/8 drive.

   

Three Larger Sizes in a Convenient Set
The three largest tap sockets, are now packaged in a three piece set. Ideal for use where a T handle won't fit, especially in restricted areas. For larger, fractional M.C.T.I. standard taps. #9 socket is 5/8" (16mm), #10 is for 11/16" (18mm) and #11 is for 3/4". Sockets contained in a vinyl holder.

Time-Sert taps 13mm to 16mm metric / 5/8 to 3/4 inch. 
use 1/2 drive socket.

   
 

Enables You To See A round Corners
2 1/4" diameter mirror swivels to any position. Length extends from 10" to 14". Has an insulated vinyl grip.

 

STRAIGHT TAP WRENCH
Straight Tap Wrench, Length 5 Inches, Hand Taps 
Capacity 1/16 to 1/4 Inch, Taps M1.5 to M6
wrench number 00 P/N C67201

 

T-HANDLE WRENCH
T- handle wrench, Length 2-3/4 Hand Taps 
Capacity 1/16” to 1/4” Inch Taps M1.5 to M6
wrench number T11 P/N C67208
Time-Sert taps M3 - M5 

 

Straight Tap Wrench, Length 11 Inches, Hand Taps
Capacity 5/32 to 1/2 Inch, Taps M4 to M12
wrench number 5 P/N C67202 
Time-Sert taps 4-40 - 7/16 Inch, M3 - M11 Metric
T- handle wrench, Length 3-5/8 Hand Taps 
Capacity 7/32” to 1/2” Inch Taps M5 to M12
wrench number T12 P/N C67209 
Time-Sert taps M5 - M11 
Straight Tap Wrench, Length 15 Inches, Hand Taps
Capacity 5/32 to 3/4 Inch, Taps M4 to M19
wrench number 6 P/N C67203
Time-Sert taps 1/4 - 9/16 Inch, M5 - M14 Metric
 
Straight Tap Wrench, Length 19 Inches, Hand Taps
Capacity 1/4 to 1-1/8 Inch, Taps M12 to M28 
wrench number 7 P/N C67204

 

 
Straight Tap Wrench, Length 40 Inches, Hand Taps
Capacity 3/4 to 1-5/8 Inch, Taps M19 to M40 
wrench number 8 P/N C67205
 

Removes broken bolts 5/8 to 7/8.

If removing a Time-Sert insert, this tool will remove
inserts from 1/2 to 9/16 inch or 12mm to 14mm metric.

Made from hardened tempered alloy steel. Use when a screw or bolt has broken off while still in the fastening hole. 5 pc set 3/32 to 5/8

If removing a Time-Sert insert, this set will remove inserts from 4-40 to 7/16 inch or 4mm to 11mm metric.

 

Removes broken bolts 7/8 to 1-1/8.

If removing a Time-Sert insert, this tool will remove inserts from 5/8 to 3/4 inch or 16mm to 20mm metric.

Removes broken bolts 1-1/8 to 1-3/8.

If removing a Time-Sert insert, this tool will remove our 3/4 pipe insert.

Time Fastener does not sell this tool! 
Rotunda Sparkplug Puller Tool. 
This tool is used to remove separated or broken spark plug casing on the Ford 3 valve spark plug M16x1.5. 
LINK: SPX Spark plug removal tool
 303-1203

 
Link: Read more info. on Ford forums #21 on page 

 

Can TIME-SERTs be installed in blind holes?

Yes TIME-SERTs can be installed in blind holes.
A basic dimension we give is .250 inches or 6.3mm deeper hole, than the insert itself.
This is the relief angle length of the tap we have to account for to get a full thread. 
This can vary as small taps will have shorter relief angle length than larger taps. 
Again this is the length from the tip of the tap to the first "full" thread.

The extra depth also gives us enough room for the install driver to slightly pass thru the bottom of the insert to expand the last few threads, locking it in place.
Example.  The blind hole depth for a 5/16-18x.450 should be a minimum of .700 inches or 17.8mm deep.
Insert length .450 + relief angle of tap .250 =.700 inches or 17.8mm Hole Depth. 

Another thing to keep in mind when repairing a blind hole application is that you "do not" want to bottom out the driver tool on installation. There is a simple method to safeguard against bottoming the tool out, by placing a visual mark the driver tool. 
BEFORE installing the insert, place the driver tool into the hole and mark the tool at the point it can't enter any further. Use a ink marker or even use a small strip of electrical tape around the driver. This way we know exactly how deep the hole is and there is no danger of bottoming the tool out.

Question:
A common question about repairing drain pans on the vehicle
is how do you keep chips from entering the drain pan?

Answer:
Using some general purpose grease on the drill and tap will help
prevent chips from going into the drain pan. Using a low RPM or
drilling by hand would further reduce the chips into the pan. 
Because we are only removing the old threads with the drill, there 
will only be a minimal amount of material removed.

Optional tip to keep chips out of the pan would be pouring the old oil 
back through pan to flush any remaining chips as it drains. 
Also remember the filter is there to catch any debris from normal engine wear.

INCH KITS
 

INSERT

DRILL

C.BORE

TAP

SIZE

DRILL 
SIZE

MIN.
DIA

MIN.
DEPTH

MAJOR 
DIA.

4-40
#31
.120
.170
.055
.147
6-32
#26
.147
.218
.070
.182
8-32
#17
.173
.241
.065
.208
10-24
13/64
.203
.288
.075
.247
10-32
13/64
.203
.274
.075
.234
12-24
#1
.228
.307
.075
.265
1/4-20
17/64
.265
.352
.075
.319
1/4-28
G
.261
.340
.075
.300
5/16-18
21/64
.328
.430
.085
.388
5/16-24
P
.323
.419
.080
.368
3/8-16
X
.397
.495
.085
.460
3/8-24
W
.386
.473
.080
.432
7/16-14
29/64
.453
.571
.110
.534
7/16-20
29/64
.453
.547
.085
.506
1/2-13
33/64
.515
.648
.110
.604
1/2-20
33/64
.515
.610
.085
.569
9/16-12
19/32
.593
.711
.130
.675
9/16-18
37/64
.578
.668
.110
.638
5/8-11
21/32
.656
.787
.135
.748
5/8-18
41/64
.640
.740
.110
.701
3/4-10
25/32
.781
.953
.135
.885
3/4-16
49/64
.765
.870
.110
.835
.

Using 12 point sockets to 
turn squares on kit tools :

Our tooling is supplied with square drives.
Normally you would use a TAP-WRENCH on taps or tools with squares.
But you will probably not have enough room for a tap wrench because of
clearance issues with a frame rail or some obstruction. Square drive 
sockets are another option. If you do not have square drive sockets you
may optionally try to use 12 point sockets to drive the squares on tools.
12 point sockets generally will hold a square better than a 6 sided socket. 

EXAMPLE FOR M14x1.5 DRAIN PAN KIT 12 POINT SOCKETS.
1) Drill square = 1/2 inch 12 point socket. 
2) CounterBore square = 7/16 inch 12 point socket.
3) Tap square = 7/16 inch 12 point socket .
4) Driver tool square = 3/8 inch 12 point socket.

This is only one possible solution to turning a tool with a square drive.